Ошибка принтера hp 610000f6

hp-concentra-wrapper-portlet

Actions

Issue

The error code ‘0x610000f6‘ message displays on the control panel, and the product does not print.

Solutions

Try the following solutions in the order presented to resolve the issue. When one of the solutions resolves the issue, there is no need to continue troubleshooting.

Video of clearing a carriage jam

The following video demonstrates the steps for clearing a carriage jam.

note:

This video shows the HP Photosmart Plus All-in-One Printer series (B209), but the steps are the same for your printer.

Solution one: Turn the printer off, and then on again

Press the Power button ( ) to turn off the product. If the product does not turn off, continue to the next solution.
Wait 60 seconds.
Press the Power button ( ) to turn on the product.

If these steps resolved the issue, you do not need to continue troubleshooting.
If the issue persists, continue to the next solution.

Solution two: Clear any jammed paper

Jammed paper can cause the carriage to stall. Follow these steps to clear a paper jam.

Step one: Remove any loose paper

caution:

Do not remove jammed paper at this stage. Trying to clear jammed paper from the front of the product can damage theprint mechanism.

Step two: Clear the paper jam

Use the following steps to check for and remove jammed paper from the back of the product.

Press the Power button () to turn off the product.
Disconnect the power cord from the back of the product.
Push the buttons on either side of the rear access panel, and then pull the panel away from the product.
Gently pull the paper out of the rollers.

caution:

If the paper tears while removing it from the rollers, check the rollers and wheels for torn pieces of paper that might remain inside the product. If any torn pieces of paper remain inside the product, more paper jams are likely to occur.
Reattach the rear access panel. Gently push the door forward until it snaps into place.
Reconnect the power cord to the back of the product.
Press the Power button () to turn on the product.

If these steps resolved the issue, there is no need to continue troubleshooting.
If the issue persists, see the next step.

Step three: Open the top cover, and then clear the paper jam

Use the following steps to open the top cover, and then clear the paper jam.

Press the Power button () to turn off the product.
Disconnect the power cord from the back of the product.
Open the cartridge access door.

Figure : Open the cartridge access door
Manually move the carriage to one side of the product.
If there is paper jammed in the product, gently remove the paper through the top of the product.

warning:

Do not reach into the device when it is on and the carriage is stuck as this could cause an electrical shock. Always turn the product off before you remove any paper jam.
Close the cartridge access door.

Figure : Close the cartridge access door
Press the Power button () to turn on the product.
Try printing again.

If these steps resolved the issue, you do not need to continue troubleshooting.
If the issue persists, continue to the next solution.

Solution three: Make sure that the carriage moves freely

Follow these steps to make sure that the carriage moves freely.

Disconnect the power cord and the USB cable from the back of the product.

caution:

Do not reconnect the power cord and USB cable until instructed to do so.
Open the cartridge access door.

Figure : Open the cartridge access door
Press down firmly on the carriage latch handle to close it completely.

Figure : Carriage latch handle in the down position

note:

If the latch handle is up, it results in incorrectly seated cartridges and the product does not function correctly.
Check whether the carriage can move freely from one side of the product to the other.Apply moderate pressure to one side of the carriage, and then push it back and forth in the product.

warning:

You must disconnect the power cord to move parts by hand without the risk of an electrical shock.
Remove any debris or obstructions from the carriage path.
Close the cartridge access door.

Figure : Close the cartridge access door
Reconnect the power cord and the USB cable to the back of the product.
Press the Power button ( ) to turn on the product.
Try printing again.

If these steps resolved the issue, you do not need to continue troubleshooting.
If the issue persists, continue to the next solution.

Solution four: Remove and reinstall the cartridges

The product might indicate a carriage jam error if a cartridge is not installed correctly. Follow these steps to make sure that the cartridges are installed correctly.

Step one: Remove the cartridges

Use these steps to remove the cartridges.

Make sure that the product is turned on.
Use the access handles on the sides of the product to open the cartridge access door.

Figure : Open the cartridge access door

note:

Wait until the carriage is idle and silent before proceeding.
Press the tab on each cartridge, and then remove each cartridge from its slot.

Figure : Remove the cartridges

Step two: Reinstall the cartridges

Use these steps to reinstall the cartridges.

Slide each cartridge into its empty slot until it clicks into place and seats firmly in the slot. Make sure that the icon on each cartridge matches the shape and color of the icon on the slot you are inserting the cartridge into.

Figure : Install the cartridges
Close the cartridge access door.

Figure : Close the cartridge access door
Try printing again.

If these steps resolved the issue, you do not need to continue troubleshooting.
If the issue persists, continue to the next solution.

Solution five: Plug the product directly into a wall outlet

Plug the product directly into a wall outlet to make sure the power source is functioning correctly.

Disconnect the power cord from the back of the product.
Disconnect the power cord from any power strips or surge suppressors, and then plug it directly into a wall outlet.
Reconnect the power cord to the back of the product.
Try printing again.

note:

If the product prints when plugged directly into a wall outlet, the power strip or surge protector might not be allowing enough voltage to reach the product.

If these steps resolved the issue, you do not need to continue troubleshooting.
If the issue persists, continue to the next solution.

Solution six: Reset the printer, and then print a status report

Step one: Reset the printer

Use these steps to reset the printer

Press the Power button () to turn off the product.
Disconnect the USB cable from the product.
Disconnect the power cord from the product, and then wait 60 seconds.
Unplug the power cord from the wall outlet.
Plug the power cord back into the wall outlet.
Reconnect the power cord to the back of the product.
Press the Power button () to turn on the product.
Reconnect the USB cable to the back of the product, and then reconnect it securely to the product.

Step two: Print a status report

Use the following steps to print a status report from the product control panel.

Load plain white paper in the input tray.
On the control panel Home Screen, touch the right arrow () to view more options.
Touch Setup ().
Touch Tools.
Touch Printer Status Report. The status report prints.

If these steps resolved the issue, you do not need to continue troubleshooting.
If the issue persists, continue to the next solution.

Solution seven: Service the product

Service or replace your HP product if the issue persists after completing all the preceding steps.

Go to Contact HP Customer Support to schedule a product repair or replacement. If you are in Asia Pacific, you will be directed to a local service center in your area.

To confirm your warranty status, go to HP Product Warranty Check. Repair fees might apply for out-of-warranty products.

Flag

United States

hp-detect-load-my-device-portlet

Actions

Источник

ошибка 0-610000f6

После простоя сутки при включении HP photosmart b110b выдал ошибку 0*610000f6 . Печатать отказался :cry_ing: каретка дергается туда сюда. т.е. уходит влево там пару раз дергается, потом возвращается вправо там также дергается потом щелк и ошибка и стоит молча, бумагу не захватывает. Выдернул кабель откл. от питания через 30 сек. вкл. не помогло. Сбросил на заводские вроде восстановился. Смотрел шлейф СНПЧ вроде нормально каретке не мешает. Задний лоток проверял на месте. Что это ещё может? :nez-nayu: Сейчас вроде работает по стоит вкл. посмотрю что будет.

KiborG: Корабельный попугай; Сообщения: 28; Зарегистрирован: 28 дек 2010, 18:12; Благодарил (а): 1 раз.; Поблагодарили: 6 раз.

Re: ошибка 0-610000f6

Leidenschaft » 22 фев 2012, 07:00

«Меж нами нет иных преград, чем кем являемся мы сами»

За это сообщение автора Leidenschaft поблагодарил:: BURSTEN

Leidenschaft

Инженер OCP

Сообщения: 1311

Зарегистрирован: 10 сен 2010, 19:35

Откуда: Омск

Благодарил (а): 255 раз.

Поблагодарили: 503 раз.

Профиль
Сайт

Re: ошибка 0-610000f6

KiborG » 22 фев 2012, 08:50

все что там написано я читал уже и проверил. Шлейф и все остальное нормально. У меня тем более он проложен по теме установка СНПЧ без разборки, так лучше получилось. А с разборкой там шлейф болтается не нравится мне что то это. Там фиксатор нужен какой-нибудь чтобы его влево не тянуло. Сейчас вроде работает нормально может где шестерня какая-нибудь не так встала, потому что треск сильный.

KiborG: Корабельный попугай; Сообщения: 28; Зарегистрирован: 28 дек 2010, 18:12; Благодарил (а): 1 раз.; Поблагодарили: 6 раз.

Re: ошибка 0-610000f6

Leidenschaft » 22 фев 2012, 08:54

KiborG писал(а):шестерня какая-нибудь не так встала, потому что треск сильный.

по звуку надо искать и смотреть. такие аппараты на вес золота сейчас.

«Меж нами нет иных преград, чем кем являемся мы сами»

Leidenschaft

Инженер OCP

Сообщения: 1311

Зарегистрирован: 10 сен 2010, 19:35

Откуда: Омск

Благодарил (а): 255 раз.

Поблагодарили: 503 раз.

Профиль
Сайт

Re: ошибка 0-610000f6

KiborG » 22 фев 2012, 18:14

Leidenschaft писал(а):

KiborG писал(а):шестерня какая-нибудь не так встала, потому что треск сильный.

по звуку надо искать и смотреть. такие аппараты на вес золота сейчас.

Заметил что в магазинах не стало их, куда они подевались интересно.

KiborG: Корабельный попугай; Сообщения: 28; Зарегистрирован: 28 дек 2010, 18:12; Благодарил (а): 1 раз.; Поблагодарили: 6 раз.

Re: ошибка 0-610000f6

Leidenschaft » 22 фев 2012, 20:07

KiborG писал(а): куда они подевались интересно.

сняли с пр-ва :-(

«Меж нами нет иных преград, чем кем являемся мы сами»

Leidenschaft

Инженер OCP

Сообщения: 1311

Зарегистрирован: 10 сен 2010, 19:35

Откуда: Омск

Благодарил (а): 255 раз.

Поблагодарили: 503 раз.

Профиль
Сайт

Вернуться в СНПЧ для HP

Перейти:

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 1

Источник

—}}

��
��
��
�� / Covid-19
��
��
��
��
��
��
��
��
��
��
��
4�4 ��
��
��
��
��
��
KIA-��
��
Hyundai ��
VAG ��
��
�� : ��
��-�� (�� , ��)
��
�� : ��
�� : ��
�� : ��
�� : ��
�� : ��
�� : �� , ��
�� : ��
�� : ��
�� : ��
�� : ��
�� -��
��
�� : ��
�� : �� (��)
�� : ��-�� (��)
�� : ��
�� : ��
�� : �� , ��
�� : ��
�� : ��
��
�� — ��
�� — ��
�� — ��
�� — �� , ��
�� — ��
��
��
�� — ��
�� — ��. ��
�� — ��: ��
�� — ��: ��
�� — ��: �� , ��, ��
��
�� (��)
�� . ��
�� (�� )
��
��
��
��
��
��
��
��
��. ��.
��
��
��
��
��
��
��
��
��
��
��
��
��, ��, ��
��
��
��
��
��
��
��
��
�� : ��
�� : ��
��
��
��
��
��
��-��
GPS ��
��
��-��
��
��. � ��
��
�� PR
��
��
��
��
��
��
��
��
��
��
��
�� (��)
��
��
��
��
��
��
��
��, ��, ��
��, ��, ��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
�� (��. �� )
��
�� (�� .)
��
��
�� (�� )
�� (�� -��)
�� (�� -��)
�� (�� ., � �� 18)
�� (�. ��)
�� (��. �� )
�� (�� -��)
�� (�� -��)
�� . (�� )
�� .
�� .
�� . (60-�� .)
�� (�� .)
��
��
��
��
��
�� iHerb
��
��
��
��
��
�� !
��-�� -��
��
��
��
��
��
�� !
��
��-��
��
��
��
��
��
��
�� (��)

�� .
�� .

��
��
��-��

�� (�� . �� -��)

� �� NN.RU

� �� NN.RU, �� .

�� , �� .

� ��

��

�� hp photosmart d5463 � �� 0�610000f6. �� .
�� , �� , �� )
�� -�� — ��

TelepuzziK ��(�)
��

�� ???
�� ݣ ��
�� — �� )))
��

�� ?

��. ��

�� ? �� , �� . � �� .

�� . �� .
�� -�� : �� -��

� �� NN.RU

� �� NN.RU, �� .

�� , �� .

� ��

��

�� .
�� .

��
�� (��)
��
��

Источник

Want to fix HP Printer Error 0X610000F6 on your HP Printer? Then, read this article completely. Here, you will find the different ways you can employ to fix the HP Printer Error 0X610000F6 in the HP Printer. So, to resolve the HP Printer Error 0X610000F6, simply perform the troubleshooting steps available here in the given order.

Different Ways to Fix Error 0X610000F6

HP Printer Error 0X610000F6 also known as Carriage Jam Error occurs very often in the Photosmart HP Printers. When a jam occurs in the printer due to paper scraps or due to any other reason, the printer stops working and it doesn’t print any document. At that time, the printer shows an error message ‘0X610000F6’ or ‘Carriage Jam’ on its LCD screen. The main reasons behind this HP Printer Error 0X610000F6 are jamming of foreign objects or defaults in cartridges. To eliminate this HP Printer Error 0X610000F6 on your own, apply any one of the solutions given below to your HP Printer.

How to Fix HP Printer Error 0X610000F6?

Method 1: Turn OFF and Turn On your Printer

First of all, by pressing the power button turn off your HP Printer. If your printer doesn’t turn off, then go for method 2 immediately by stopping this method 1.
Wait for one minute and again turn on your printer by pressing the power button of your printer.
Now, check if the HP Printer Error 0X610000F6 is resolved or not. If the 0X610000F6 error is still displaying, then perform the method 2.

Method 2: Clean all the Paper materials that are Jammed

Unplug all the USB cables and power cable of your HP printer.
Open the printer’s tray and look for any paper materials. If found, remove them carefully.
Now open the rear access door of the printer and see that any paper scraps are stuck inside the printer and clean them if present.
Close the rear access door and place the papers into the printer’s tray.
Now plug back all the USB cables and power cable to your HP printer.
Switch on your printer by pressing the button and print a sample document.
If it doesn’t do the print job, then perform the method 3.

Method 3: Check Whether the Printer Cartridges are properly installed or not and Remove any jammed papers

Unplug the power cable and all the USB cables of your printer.
Now open the cartridge access door and press the carriage latch carefully so that it closes completely.
Now check if the cartridges are able to move from one side to another side freely and check for any jammed papers.
If the obstructions are found, remove them carefully.
Make sure that the cartridges are properly seated or not.
Now close the cartridge access door carefully and plug back all the USB cables and power cord to your HP Printer.
Turn ON your HP Printer by pressing the power button of the printer and perform a print task again and fix HP Printer Error 0X610000F6.

Please contact the customer support of the HP printer in case the issue prevails.

Источник

Ошибка принтера hp 610000f6

Issue

Solutions

Video of clearing a carriage jam

Solution one: Turn the printer off, and then on again

Solution two: Clear any jammed paper

Step one: Remove any loose paper

Step two: Clear the paper jam

Step three: Open the top cover, and then clear the paper jam

Solution three: Make sure that the carriage moves freely

Solution four: Remove and reinstall the cartridges

Step one: Remove the cartridges

Step two: Reinstall the cartridges

Solution five: Plug the product directly into a wall outlet

Solution six: Reset the printer, and then print a status report

Step one: Reset the printer

Step two: Print a status report

Solution seven: Service the product

ошибка 0-610000f6

Re: ошибка 0-610000f6

Re: ошибка 0-610000f6

Re: ошибка 0-610000f6

Re: ошибка 0-610000f6

Re: ошибка 0-610000f6

Кто сейчас на конференции

Different Ways to Fix Error 0X610000F6

How to Fix HP Printer Error 0X610000F6?

Method 1: Turn OFF and Turn On your Printer

Method 2: Clean all the Paper materials that are Jammed

Method 3: Check Whether the Printer Cartridges are properly installed or not and Remove any jammed papers

А вот еще интересные материалы: